Marsh Bellofram’s General Purpose Type 40 Pressure Regulator is a reliable precision unit designed for instrumentation and general purpose use. Test data for the Type 40 regulator shows excellent performance characteristics compared with those of similar units presently on the market. The Type 40 regulator is generally superior in regulated pressure vs. flow, forward-to-reverse flow offset, supply pressure sensitivity, repeatability and stability.
Ruggedly designed and constructed, the Type 40 has housings of diecast
aluminum. Every regulator is finished with vinyl paint (which resists scratching, weathering and other physical abuse) and is pressure and leak tested prior to shipment from the factory. Careful design and quality materials throughout assure long, trouble-free operation in the most difficult industrial environments. A rubberized, soft-seat valve stem provides positive shut-off and “forgives” dirt or other foreign matter. An aspirator maintains downstream pressure and compensates for droop when high flow occurs. The gauge port is convenient for gauge installation and can also be used as an additional full flow outlet.
The Type 40 regulator has a 60-mesh 304 stainless steel screen to block foreign particles from entering the output stream. The design of these regulators is especially well suited to pilot-operated controllers and instruments, as well as applications such as air chucks, air spray guns, air cylinders and actuators, and a wide range of industrial pneumatic systems and equipment.
Part Numbers:
Part Number
Port Size
Set Point Range
BAR
psig
960-063-000
1/4 NPT
0-0.7
0-10
960-064-000
1/4 NPT
0-2.1
0-30
960-065-000
1/4 NPT
0-4.1
0-60
960-066-000
1/4 NPT
0-8.3
0-120
To order BSPT threads (including the gauge port) add “BSPT” to end of part number.
Options:
Option Ordering Matrix:
Replace the last three digits of the part number with digits from the table below. If more than 2 combination needed, Consult Factory.
OPTION
1
2
3
5
6
7
8
9
10
11
1
Fluorocarbon Pintle
001
021
031
051
061
071
081
091
101
111
2
Non-Relieving
002
032
052
072
082
092
112
3
Knob
003
053
063
073
083
103
113
5
Epoxy Coating
005
065
075
085
095
105
115
6
Tapped Vent
006
076
086
096
106
116
7
Mounting Bracket
007
087
097
107
117
8
Pressure Gauge
008
098
108
118
9
Tamper-Resistant Cover
009
109
119
10
Soft Relief Seat
010
110
11
Florocarbon Diaphragm
011
Fluorocarbon Pintle: A special elastomeric pintle used where elements in the supply air, such as flame retardant synthetic lubricants, are particularly destructive to ordinary pintle material.
Non Relieving: Used in applications where it is desirable to relieve pressure downstream of the regulator, for some constant flow applications, and where the gas flowing through the regulator must not escape at the regulator. Non-relieving regulators should not be used for low or no flow applications.
Corrosive Resistant Epoxy finish: An epoxy paint applied to the body and bonnet of the regulator exterior surfaces to provide increased corrosion resistance.
Mounting Bracket: Steel (dichromate finish) bracket for side mounting. P/N: 607-000-057
Knob: Option to replace the square head pressure adjusting screw.
Tapped Vent: Allows installation of plumbing to capture exhaust air.
Pressure Gauge: Dual scale 2 in. (50.8 mm) gauges. Ranges include 0-30 psig (0-200 kPa), 0-60 psig (0-400 kPa), 0-100 psig (0-700 kPa) and 0-160 psig (0-1100 kPa). When specified with regulator, the correct range will be supplied. For NPT versions only.
Tamper Resistant Cover: An aluminum tubular cover placed over a slotted head adjusting screw and screwed onto the bonnet of the regulator with a wrench. Prevents ordinary hand adjustments.
Soft Relief Seat: Used in applications where it is desirable to reduce the standard bleed rate from 6 SCFH [0.17 m3hr] to less than 0.1 SCFH [0.003 m3hr].
Fluorocarbon Diaphragm: Diaphragm as well as all seals are made of fluorocarbon elastomer to prevent deterioration from elements in the air supply, such as flame retardant synthetic lubricants normally destructive to standard Nitrile material.
